
IATF 16949 and ISO 9001 Certified | Leaf Chains to DIN and ISO 4347 | Since 1976
On a forklift, the lifting chain carries the load and everything that depends on it. Mast chains work under high tensile load, run over pulleys thousands of times a day and must never fail without warning. That is why forklift chain selection is first and foremost a safety decision.
Zimaş Zincir manufactures flyer chains (leaf chains) and Gall chains for forklift and lifting equipment manufacturers, service companies and spare parts dealers in its integrated plant in Bursa.
🏭 Transmission Chain Manufacturing in Türkiye Since 1976
Founded in 1976 in the Bursa Demirtaş Organized Industrial Zone, Zimaş Zincir ve Makine San. Tic. A.Ş. is the first company of Topbaş Group. Every production stage, from material preparation to heat treatment and assembly, is carried out in-house.
- ✓ Over 3,500 chain dies for a wide production range
- ✓ Over 5,000 tons of annual heat treatment capacity
- ✓ Exports to Europe, the Middle East and neighboring countries
- ✓ IATF 16949, ISO 9001, ISO 14001, ISO 27001 certifications
⛓️ How a Flyer Chain Works
A flyer chain consists only of plates and pins, without rollers. It does not engage with a sprocket; it runs over a pulley and transmits tensile force. This makes it ideal for lifting applications such as forklift masts.
🔢 Lacing and Capacity
The load capacity of a flyer chain depends on its pitch and lacing. For example, a 4x6 lacing means 4 inner and 6 outer plates on each pin. Higher lacing means higher breaking strength.
Zimaş Zincir in Figures
What Lifting Equipment Expects from a Chain
Lifting chains carry loads directly, so the requirements are strict:
- High breaking strength: A sufficient safety factor against the working load.
- Fatigue resistance: Durability under thousands of lifting cycles over pulleys.
- Low initial elongation: Pre-stretched chains reduce elongation after installation.
- Standard compliance: Dimensions to DIN and ISO 4347 for direct interchangeability.
- Correct end connections: Anchor bolts and clevises matched to the chain series.
Application Areas
Zimaş lifting chains are used in forklifts, warehouse equipment, lifting platforms and heavy lifting units. All our industry solutions are listed on the industrial chain solutions by sector page.
Forklifts and Stackers
- Mast chains: For diesel, LPG and electric forklifts
- Stackers and reach trucks: Lifting chains for warehouse equipment
- Free lift cylinders: Chains for free lift systems
Lifting Platforms and Lifts
- Scissor and vertical mast platforms: Lifting chains for platforms
- Goods lifts: Chains for mezzanine and goods lifts
- Vehicle service lifts: Chains for workshop lifts
Hoisting and Lifting Units
- Counterweight systems: Chains for counterweight guidance
- Machine mounted lifting units: Lifting and lowering chains
- Automated warehouses: Chains for vertical movement units
Transport and Construction Equipment
- Telehandlers: Boom and lifting chains
- Truck mounted cranes and tippers: Lifting chains
- Very heavy, low speed lifting: Gall Chains for high loads
Chain Selection by Application
| Application | Recommended Zimaş Product | Why |
|---|---|---|
| Forklift and stacker masts | Flyer Chains (LH / AL series) | Standard and capacity matched to the origin of the equipment |
| Light lifting in narrow spaces | Flyer Chains (LL series) | Low profile design |
| Very heavy load at low speed | Gall Chains | Large pin, bushing and plate structure |
Why Zimaş Flyer Chains
📐 Standard Compliance
LH, AL and LL series produced to DIN and ISO 4347 dimensions for direct interchangeability.
🔥 Heat Treatment and Testing
Plates and pins are heat treated in-house, and tensile tests are reported.
📏 Pre-Stretching
Chains are pre-stretched to reduce initial elongation after installation.
- Ready to fit: Chains can be delivered cut to length, with the required end connections.
- Quality systems: Production certified to IATF 16949, ISO 9001 and ISO 14001.
Forklift Chain Inspection and Replacement
- Elongation measurement: Measure the chain over a fixed number of pitches and replace it once the manufacturer's limit is exceeded.
- Visual inspection: Check for cracked plates, rotated or protruding pins and corrosion.
- Lubrication: Lubricate the chain regularly so that oil penetrates between the plates.
- Equal tension: On masts with two chains, make sure both chains carry equal tension.
- Replace in pairs: Replace both chains of a mast at the same time, together with worn anchor bolts.
Frequently Asked Questions
1. How do I determine the size of my forklift chain?
The series, pitch and lacing (for example LH 1234 or 4x4) are usually stamped on the plates. If the marking is not readable, you can send us a sample or the pitch and plate dimensions.
2. What is the difference between LH and AL series flyer chains?
LH series chains have more and thicker plates and are designed for higher loads, while AL series chains are a lighter duty series for lower loads. The correct series depends on the equipment and its origin.
3. When should a forklift chain be replaced?
A forklift chain should be replaced when its elongation exceeds the manufacturer's limit, or when cracked plates, damaged pins or heavy corrosion are found.
4. Why does a flyer chain not run on a sprocket?
A flyer chain has no rollers, so it is not designed to engage with sprocket teeth. It runs over a pulley and is used only to transmit tensile force in lifting applications.
🏭 Related Sector Solutions:
All Sector Chain Solutions Cement Industry Automotive Industry Food Industry Packaging Industry Agricultural Machinery Recycling and Solid Waste Iron and Steel Industry Oil, Gas and Drilling Mining and Quarries About Us: History and Certificates Manufacturing CompetenciesSafe Lifting Starts with the Right Chain
Share your equipment model and chain size, and our team will determine the right lifting chain for you.
Request a QuoteChain Supplier for Forklifts and Lifting Equipment
Zimaş manufactures flyer chains and Gall chains for forklift and lifting equipment manufacturers, service companies and dealers in its integrated plant in Bursa.
As part of Topbaş Group, we continue to serve the lifting equipment sector with the confidence that comes from dynamism, experience, consistent quality and customer satisfaction.
Zimaş Zincir ve Makine San. Tic. A.Ş. | Topbaş Group
Lifting Chain Supplier Since 1976
www.zimaszincir.com.tr